CH01-chassie-build-instructions
01_HW-placment
01_HW-placment
02_useful-tools
02_useful-tools
03_separate-parts
03_separate-parts
04_trim
04_trim
05_keep_slider-in-front
05_keep_slider-in-front
06_keep_slider-in-front
06_keep_slider-in-front
07_klean-battery-holes
07_klean-battery-holes
08_snapin-battery-magnets
08_snapin-battery-magnets
09_snapin-battery-magnets
09_snapin-battery-magnets
10_battery-magnets
10_battery-magnets
11_presson_spurgear_17.5mm
11_presson_spurgear_17.5mm
12_prep-motor-pod
12_prep-motor-pod
13_motor-all-inn
13_motor-all-inn
14_inst-mpod
14_inst-mpod
15_inst-mpod
15_inst-mpod
16_push-all-inn
16_push-all-inn
17_prep_axel-and-bushings
17_prep_axel-and-bushings
18_fasten-with-bolts
18_fasten-with-bolts
19_adjust-gears
19_adjust-gears
20_cut-excess-to-clear battery
20_cut-excess-to-clear battery
21_prep-frontend
21_prep-frontend
22_clear-2mm-holes
22_clear-2mm-holes
23_clear-2mm
23_clear-2mm
24_clear-2mm
24_clear-2mm
25_clear-2mm
25_clear-2mm
26_clear-1mm-holes
26_clear-1mm-holes
27_DON'T_touch
27_DON'T_touch
30_clear-2mm
30_clear-2mm
31_clear-1mm
31_clear-1mm
32_clear-1mm(Small)
32_clear-1mm(Small)
33_find-your-micro-servo
33_find-your-micro-servo
34_place-servo-before-closing
34_place-servo-before-closing
35_place_nail-in-knuckle
35_place_nail-in-knuckle
36_align-squeece-through
36_align-squeece-through
37_repeat
37_repeat
38_magnest-same-wayin-this-part
38_magnest-same-wayin-this-part
39_magnest-same-wayin-this-part
39_magnest-same-wayin-this-part
40_opposite-polarity-in-servoconnector
40_opposite-polarity-in-servoconnector
41-shall-repell
41-shall-repell
42-180-turnes-will-attract
42-180-turnes-will-attract
43-connect-linkage-to-knukles
43-connect-linkage-to-knukles
44-FREE-moving-no-snag
44-FREE-moving-no-snag
45_2mm
45_2mm
46_also-prep_small-screw-connector
46_also-prep_small-screw-connector
46_prep-guide
46_prep-guide
47_guide
47_guide
48_guide
48_guide
49_guide-conn-screew
49_guide-conn-screew
50_guide-conn-screw
50_guide-conn-screw
51_connect-servo-linkage-BEFORE
51_connect-servo-linkage-BEFORE
52_fronwheel-axle-andnut
52_fronwheel-axle-andnut
53_radio-and-esc
53_radio-and-esc
54-prep-battery
54-prep-battery
55_check-battery-fit
55_check-battery-fit
60_adj-guide-mag-through-hole
60_adj-guide-mag-through-hole
bodymount
bodymount

Steering should move by magnet force.

Make sure theiy move freely.

The best tool to use is a 1-2 mm allan wrench to push the magnet out when needed.

Use a finger to push against.